Tweet
You could take the rotor completely off and ride it a short distance on just the battery power to check. Just remember to put the stator cover back on before you start the engine so you don't blow the oil galley plug and oil across the garage.
-
Greg
Everybody is a genius. But if you judge a fish by its ability to climb a tree, it will live its whole life believing that it is stupid.”
― Albert Einstein
80 SG Ol' Okie;79 engine & carbs w/pods, 45 pilots, 140 mains, Custom Mac 4 into 2 exhaust, ACCT,XS850 final drive,110/90/19 front tire,TKat fork brace, XS750 140 MPH speedometer, Vetter IV fairing, aftermarket hard bags and trunk, LG high back seat, XJ rear shocks.
The list changes.
-
exactly what i was going to try greg. :-)Originally posted by BA80 View Post
other than that and what ron suggested i cant think of anything
else to try except for tearing into it.pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
-
Good luck Pete. Hopefully you'll find the rotor out of balance or bent and it'll be an easy fix.
Keep us posted. I'm interested in learning what you find.Greg
Everybody is a genius. But if you judge a fish by its ability to climb a tree, it will live its whole life believing that it is stupid.”
― Albert Einstein
80 SG Ol' Okie;79 engine & carbs w/pods, 45 pilots, 140 mains, Custom Mac 4 into 2 exhaust, ACCT,XS850 final drive,110/90/19 front tire,TKat fork brace, XS750 140 MPH speedometer, Vetter IV fairing, aftermarket hard bags and trunk, LG high back seat, XJ rear shocks.
The list changes.Comment
-
pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
-
Hi was wondering if you found out what the problem was just would like to know.To fix the problem one should not make more assumptions than the minimum needed.
Rodan
https://www.youtube.com/watch?v=khm6...liHntN91DHjHiS
1980 G Silverbird
Original Yamaha Fairfing and Bags
1198 Overbore kit
Grizzly 660 ACCT
Barnett Clutch Springs
R1 Clutch Fiber Plates
122.5 Main Jets
ACCT Mod
Mac 4-2 Flare Tips
Antivibe Bar ends
Rear trunk add-on
http://s1184.photobucket.com/albums/z329/viperron1/Comment
-
Yeah.......what he said!
Greg
Everybody is a genius. But if you judge a fish by its ability to climb a tree, it will live its whole life believing that it is stupid.”
― Albert Einstein
80 SG Ol' Okie;79 engine & carbs w/pods, 45 pilots, 140 mains, Custom Mac 4 into 2 exhaust, ACCT,XS850 final drive,110/90/19 front tire,TKat fork brace, XS750 140 MPH speedometer, Vetter IV fairing, aftermarket hard bags and trunk, LG high back seat, XJ rear shocks.
The list changes.Comment
-
i havent spent much time on it,
ive lost motivation with it,
i took out the top engine mounts
and removed the 'outer sleeve' made
a bit of difference, couldnt get the others out
with out disconnecting the final drive,
and breaking my back,
havent been bothered stuffing around with it any more,
made a bit of difference, its got the vibration
between 3500 - 4500, but its more ridable.
im in the process of selling it all up and looking
at updating to something much newer.pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
-
I had a bearing go bad on the shaft the clutch basket sits on. It had a funky vibration and knocked out the little bearing on the clutch cover also. Unfortunately, this was a case-splitting issue to fix.
Hate to hear of you giving up on it..
Try your hardest to be the kind of person your dog thinks you are.
You can live to be 100, as long as you give up everything that would make you want to live to be 100!
Current bikes:
'06 Suzuki DR650
*'82 XJ1100 with the 1179 kit. "Mad Maxim"
'82 XJ1100 Completely stock fixer-upper
'82 XJ1100 Bagger fixer-upper
'82 XJ1100 Motor/frame and lots of boxes of parts
'82 XJ1100 Parts bike
'81 XS1100 Special
'81 YZ250
'80 XS850 Special
'80 XR100
*Crashed/Totalled, still ownComment
-
hey tod,Originally posted by trbig View PostI had a bearing go bad on the shaft the clutch basket sits on. It had a funky vibration and knocked out the little bearing on the clutch cover also. Unfortunately, this was a case-splitting issue to fix.
Hate to hear of you giving up on it..
thats where i think my problem is, before changing out the clutch
basket, fibres and steels, the bike was unridable,
its better but not right, the clutch also chatters slightly in use.
ive got 3 engines sitting here, they all need to have the cases
split with different problems to be repaired.
pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
-
Have you taken the valve cover off and verified cam timing? if its way retarded or advanced it can cause cylinder mix up @ high rpm and full ignition advance... JATDon
1979 XS1100SF "Old Man" bought by my Dad brand new in 79, customized in 80 with Vetter, Standard tank, and touring seat. I inherited in 02 when Dad passed. Been riding it since 09. No resto, bike is a survivor...
2007 RoadStar 1700 Midnight Silverado "The Black Pearl" Cobra Slash-downs, K&N filter. More mods to come
old:
1989 kawi ex500
1996 yzf-r6
1999 yzf-r1
2001 kawi zx-6r
2000 Ducati 748
2002 YZF-R1
2005 V-Star 1100 ClassicComment
-
hey don,Originally posted by ddragon63 View Post
yep was 1 of the 1st things i looked at before starting
the engine, the cam caps were on back to front but
other than that the timing is sweet, thanx anyway.pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
-
hmmm... well..... sounds like a balance issue somewhere then. or the ignition is getting way pissed as it advances. Dunno buddy. Hope you figure it out.Originally posted by petejw View PostDon
1979 XS1100SF "Old Man" bought by my Dad brand new in 79, customized in 80 with Vetter, Standard tank, and touring seat. I inherited in 02 when Dad passed. Been riding it since 09. No resto, bike is a survivor...
2007 RoadStar 1700 Midnight Silverado "The Black Pearl" Cobra Slash-downs, K&N filter. More mods to come
old:
1989 kawi ex500
1996 yzf-r6
1999 yzf-r1
2001 kawi zx-6r
2000 Ducati 748
2002 YZF-R1
2005 V-Star 1100 ClassicComment
Comment