Announcement

Collapse
No announcement yet.

Engine Guard fit question?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Engine Guard fit question?

    Does anyone know if an 80 SG three point engine guard would wit a 78E without modifications? TIA
    Nathan
    KD9ARL

    μολὼν λαβέ

    1978 XS1100E
    K&N Filter
    #45 pilot Jet, #137.5 Main Jet
    OEM Exhaust
    ATK Fork Brace
    LED Dash lights
    Ammeter, Oil Pressure, Oil Temp, and Volt Meters

    Green Monster Coils
    SS Brake Lines
    Vision 550 Auto Tensioner

    In any moment of decision the best thing you can do is the right thing, the next best thing is the wrong thing, and the worst thing you can do is nothing.

    Theodore Roosevelt

  • #2
    As far as I know, it would. The structure of all the frames is identical, as is that of the engines.
    1980 XS850SG - Sold
    1981 XS1100LH Midnight Special (Sold) - purchased 9/29/08
    Fully Vetterized and Dynojet Kit added, Heated Grips, Truck-Lite LED headlight, Accel Coils, Irridium plugs, TKAT Fork Brace, XS850LH Final Drive & Black SS Brake lines from Chacal.
    Here's my web page devoted to my bike! XS/XJ User's Manuals there, and the XJ1100 Service Manual and both XS1100 Service manuals (free download!).

    Whether you think you can, or you think you cannot - You're right.
    -H. Ford

    Comment


    • #3
      Thanks! thats what I figured but I just wanted to make sure!
      Nathan
      KD9ARL

      μολὼν λαβέ

      1978 XS1100E
      K&N Filter
      #45 pilot Jet, #137.5 Main Jet
      OEM Exhaust
      ATK Fork Brace
      LED Dash lights
      Ammeter, Oil Pressure, Oil Temp, and Volt Meters

      Green Monster Coils
      SS Brake Lines
      Vision 550 Auto Tensioner

      In any moment of decision the best thing you can do is the right thing, the next best thing is the wrong thing, and the worst thing you can do is nothing.

      Theodore Roosevelt

      Comment


      • #4
        I've a three point on my 78E, fits fine.
        Darrell
        78E
        80G project
        06FJR

        Comment


        • #5
          Yes the crash bars will fit.

          I just mounted a set on my 79 xs11 special.

          BUT, the main engine bolt may not be long enough.

          mine was not. so i cut it in the middle and
          tig welded in 3/4" of grade 5, bolt shank.

          Now it's long enough.

          it was 1/2" inch too short, i couldn't thread the nut on over the brackets.
          1979 XS1100SF Special.78 E motor/carbs, Jardine 4-2 exhaust, XS Green coils, Corbin seat, S.S. Brake lines, Hard cases, Heated grips.

          2012 FJR1300 Gen 2. Heli bar risers, R-gaza crash bars, mccruise cruise control.

          (2)2008 WR250R. Because kids outgrew others.

          2007 Suzuki V-Strom 1000. (Just added 2024) pre-crashed.

          1975 Kawasaki S1 250. My first bike. Still have it. NO I'm not selling it!!

          Most bike problems are caused by a loose nut connecting the handlebars and the seat!!

          Comment


          • #6
            +1 on the bolt length. I went to Home Depot and bought a length of all-thread, some SS washers and nylock nuts, and created my own "bolt" for mine. Unfortunately, the way mine fit (not sure if they are all the same), I have to remove the whole right-side guard to get the alternator cover off. The timing cover will come off without removing the guard on the left side though.
            1980 XS850SG - Sold
            1981 XS1100LH Midnight Special (Sold) - purchased 9/29/08
            Fully Vetterized and Dynojet Kit added, Heated Grips, Truck-Lite LED headlight, Accel Coils, Irridium plugs, TKAT Fork Brace, XS850LH Final Drive & Black SS Brake lines from Chacal.
            Here's my web page devoted to my bike! XS/XJ User's Manuals there, and the XJ1100 Service Manual and both XS1100 Service manuals (free download!).

            Whether you think you can, or you think you cannot - You're right.
            -H. Ford

            Comment

            Working...
            X