Phil's (not quite) Excellent Venturer

[MaximPhil]

Link worked for me.

Thanks DGXSER as you can see I am neither a fast or acuarte typist either.
Phil

[DGXSER]

Nice pics....I'd hate to see what you guys would do to an engine after viewing the aftermath of the Final drives!!

Nice work, very shiny things!!!!

[tarzan]

Nice job Phil.It looks like someone is getting new mufflers.

[Big Daddy Funk]

Fat Boys?

Hey can someone test the album link and report?
Tinman you still awake
Phil

Yep it works Phil. Looks like you've got a couple of fat boys.
Hope you won the mufflers too.
Rick

[MaximPhil]

Yep it works Phil. Looks like you've got a couple of fat boys.
Hope you won the mufflers too.
Rick

Hi Rick,
Apparently the mufflers are to be installed. Do we need them this Saturday? Cables should be here by then.
Phil

[Big Daddy Funk]

Sure

Hi Rick,
Apparently the mufflers are to be installed. Do we need them this Saturday? Cables should be here by then.
Phil

Could'nt hurt Phil. But we still have some work to do on the pipes.
I put your carbs and tank on it yesterday and some put on new fuel and vacuum hoses and inlne filters. My plan is to do the float adjustments today and install the air box. We could use an air filter.
Tomorrow I'll recheck the head bolt torque and the valve lash and timing chain slack adjustment.
By the end of the week the carbs should be sync'd and engine tuned.
Saturday we can check the clutch plates,work on the pipes and install the cables and flush the brake lines. If we have time we can drop the oil, filter and pan. And of course there's always cosmetics.
Is that a light I see at the end of the tunnel?

[madmax-im]

Phil pics came out XSellent! You guys are doing a splendid job!

[MaximPhil]

Oh Yes they are certainly doing a splendid job. Still plenty to do though I do belive that is a light at the end of the tunnel
Phil

[MaximPhil]

Fridge

Canadian Style refrigeration


and we did do some work too
More wirewheel , sanding and sawing for Phil while Rick worked on fabricating header to muffler connection.
Two trips to Canadian Tire for the gopher.
James could not be there so nothing got hammered to day

[MaximPhil]

Front Wheel



Picture shows how nicely the rusted rotor cleaned up. Rick insists the fork lowers are only "cleaned" not polished
Phil

[Big Daddy Funk]

Don't Eat Yellow Snow or Leave Chidren Unattended

Canadian Style refrigeration


and we did do some work too
More wirewheel , sanding and sawing for Phil while Rick worked on fabricating header to muffler connection.
Two trips to Canadian Tire for the gopher.
James could not be there so nothing got hammered to day

It would be difficult to get more Canadian than that pic unless there was maple syrup on a beavertail and a steaming bowl of poutine.
Lakeport beer is brewed in Hamilton and caesar's are the most popular coctail in the country and was invented out west.
The red cord is attached to the hell hound that zealously guards the stash.
Beg to differ with Phil though. Phil and I both got hammered BECAUSE James wasn't there.
Rick

[tinman905]

Sorry Phil I didn't hear my cell phone ringing I was out on my bike .That new Dyno Jet kit I installed is fantastic.

I will make it up to you tomorrow I am going to BigDaddy's place to weld up your new cross overs.

[Big Daddy Funk]

Sidetracked

Well we got a little sidetracked with other things for a while but Tinman built a muffler extension with crossover for the exhaust. The extension was used to move the fat boy mufflers back to a more stock position and a crossover pipe to aid tuning and provide some low pressure behind the exhaust valves.
Just a couple of valves to reshim and some soldering and shrink tubing pickup wires today.
Saturday we hope to finish installing the exhaust system and tune the bike to Phil's carbs.
A test ride is within site. Happy Birthday Phil.

[tinman905]

Here a few pictures of the crossover before paint and my new best friend







She is my new best friend because she didn't bite me

[tinman905]

Here's an up date on what we did today. BigDaddy will give more details later
I took this video using my Iphone the sound isn't as good as the real thing of course but we thing it sounds awesome




Here's Phil painting his fairing bracket.



Here is BigDaddy working on the carbs.





Here's the boys hard at work



This is a picture of my Carbtune on Phil's carbs