Anybody remember the procedure for Randy Rago's TCI quick test? It involves an analog multimeter, and you test the orange and grey lines, but I can't remember the exact procedure - as in where the probes go for the test. Unfortunately I can't find Randy's video on the web anywhere, and I'm hoping one of you fine XSives has a better memory than me.
Announcement
Collapse
No announcement yet.
Randy Rago's TCI Quick Test
Collapse
X
-
Randy Rago's TCI Quick Test
I think I have a loose screw behind the handlebars.
'79 XS11 Standard, Jardine 4/1, Dyna DC1-1 Coils, 145 mains, 45 pilots, plastic floats - 25.7mm, XV920 fuel valves, inline fuel filters, speed bleeders, Mikes XS pods, spade-type fuse block, fork brace, progressive fork springs/shocks, manual petcocks, 750 FD, Venture cam chain tensioner, SS brake linesTags: None
-
XS1100F TKAT fork brace Stock suspension. Vetter Fairing. Pingel Petcocks. Geezer voltage regulator
http://s910.photobucket.com/albums/a...t=DSCF3026.jpg
650SF
http://s910.photobucket.com/albums/a...t=DSCF2647.jpg
XS1100SG Project bike
http://s910.photobucket.com/albums/a...t=DSCF3034.jpg
-
Nope. That thread talks about the TCI quick test, but doesn't mention the specifics of the procedure.I think I have a loose screw behind the handlebars.
'79 XS11 Standard, Jardine 4/1, Dyna DC1-1 Coils, 145 mains, 45 pilots, plastic floats - 25.7mm, XV920 fuel valves, inline fuel filters, speed bleeders, Mikes XS pods, spade-type fuse block, fork brace, progressive fork springs/shocks, manual petcocks, 750 FD, Venture cam chain tensioner, SS brake lines
Comment
-
Found it! And I have to thank RR3 for the link. It didn't have the info, but it did have Randy's user ID. So I googled his ID and "tci quick test" and there it was. This is the procedure I was looking for -
Using a voltmeter set on 12VDC, connect the positive meter lead to the Orange or Grey coil lead at the TCI. Connect the negative meter lead to the black (negative) lead at the TCI. Turn on the ignition. Voltage should come right up to about 10 - 11VDC. Crank the ignition and observe the meter. Look for a wide voltage swing during cranking. A strong swing indicates that the pickups and TCI are working OK and your trouble is between the TCI and the plugs. Possibly a bad ballast resistor, bad coil, bad plug cap or just corroded connections. Repeat this test for both Orange and Grey coil leads.I think I have a loose screw behind the handlebars.
'79 XS11 Standard, Jardine 4/1, Dyna DC1-1 Coils, 145 mains, 45 pilots, plastic floats - 25.7mm, XV920 fuel valves, inline fuel filters, speed bleeders, Mikes XS pods, spade-type fuse block, fork brace, progressive fork springs/shocks, manual petcocks, 750 FD, Venture cam chain tensioner, SS brake lines
Comment
-
It's using the negative sides of the coils and the analog meter the same as a half-fast tachometer. The test can be used on the pick-up coils too using the millivolt range instead of volts.
I suppose you could just use a tach but cheap analog meters are more useful and you don't cry as much if they go tango uniform in the toolbox.-- Scott
_____
♬
2004 ST1300A: No name... yet
1982 XJ1100J: "Baby" SS Brakes, '850 FD, ACCT
1980 XS1100G: "Columbo" SS Brakes, '850 FD, ACCT
1979 XS1100SF: "Bush" W.I.P.
1979 XS1100F: parts
2018 Heritage Softail Classic 117 FLHCS SE: "Nanuk" It's DEAD, it's not just resting. It is an EX cycle.
♬
Comment
Comment