Tweet
I've just bought these on eBay. Are my fears justified?
http://www.ebay.com.au/itm/150810715...#ht_1292wt_698
Dan.
Losing his spark.
http://www.ebay.com.au/itm/150810715...#ht_1292wt_698
Dan.
Losing his spark.
-
Automotive Imbecile.
Proud owner of 'The Swiftcicle'. (Swifty for short)
'78E Full Vetter Dresser.
1196 Big Bore Kit. -
Other than it only being a single coil, what are your concerns?Nathan
KD9ARL
μολὼν λαβέ
1978 XS1100E
K&N Filter
#45 pilot Jet, #137.5 Main Jet
OEM Exhaust
ATK Fork Brace
LED Dash lights
Ammeter, Oil Pressure, Oil Temp, and Volt Meters
Green Monster Coils
SS Brake Lines
Vision 550 Auto Tensioner
In any moment of decision the best thing you can do is the right thing, the next best thing is the wrong thing, and the worst thing you can do is nothing.
Theodore Roosevelt -
I've bought two of them. I was just a bit concerned about the price, they seem too cheap really and you only get what you pay for. I was really wondering if anyone else here has experience with these coils.Automotive Imbecile.
Proud owner of 'The Swiftcicle'. (Swifty for short)
'78E Full Vetter Dresser.
1196 Big Bore Kit.Comment
-
Don't know, the seller doesn't really give any info about the specifics of the coils other than it is for a 12 volt system. None of the relevant resistance are given.Nathan
KD9ARL
μολὼν λαβέ
1978 XS1100E
K&N Filter
#45 pilot Jet, #137.5 Main Jet
OEM Exhaust
ATK Fork Brace
LED Dash lights
Ammeter, Oil Pressure, Oil Temp, and Volt Meters
Green Monster Coils
SS Brake Lines
Vision 550 Auto Tensioner
In any moment of decision the best thing you can do is the right thing, the next best thing is the wrong thing, and the worst thing you can do is nothing.
Theodore RooseveltComment
-
Hey Dan,
Well, looking at the larger image, will see if this link will work?
It looks very close to the OEM designed coils, and he specifically states it's for the 12 volt XS 11, but as Nate said, he doesn't tell you what the OHM's are, either 1.5 or 3.0...AND he also makes a mistake in describing it as for a CDI ignition system, which usually only use 0.7 ohms, whereas ours are TCI's, with the higher resistance levels!
They do NOT look anything like the Black MikesXS HT coils that burned up after 10K miles! You might want to write to him and inquire about the resistance rating....so you'll know whether you'll need to bypass your ballast resistor....but you can also check the resistance/ohms yourself once you get them in hand!
T.C.T. C. Gresham
81SH "Godzilla" . . .1179cc super-rat.
79SF "The Teacher" . . .basket case!
History shows again and again,
How nature points out the folly of men!Comment
-
Thanks chaps. I was dreading the 10k burn out I've read about MikesXS coils but these looked different. It's a bit of a 'pig in a bag' I know but they look right and that's what persuaded me. I'll check the resistance before I install them. I'll let you know how they go, they're coming from England so should be here in a week or so.Automotive Imbecile.
Proud owner of 'The Swiftcicle'. (Swifty for short)
'78E Full Vetter Dresser.
1196 Big Bore Kit.Comment
-
OK, Primary = 3 ohms, should be 1.5 +/- 10% at 20 degrees C.
Secondary = 17k ohms, should be 15k +/- 10% at 20 degrees c.
How do you think I should proceed?Automotive Imbecile.
Proud owner of 'The Swiftcicle'. (Swifty for short)
'78E Full Vetter Dresser.
1196 Big Bore Kit.Comment
-
Bypass the ballast resistor and ride it! Should work well, as T.C. said the resistance is good for the 1980 and up, or early with the ballast resistor bypassed.
I just plugged the red/white wires together, then wrapped them so they would not short(again!). I ran the green coils on my bike for quite a while with no problems once I made SURE the bypass would not short to a ground.Ray Matteis
KE6NHG
XS1100 E '78 (winter project)
XS1100 SF Bob Jones worked on it!Comment
-
Thanks Ray. I've got a heap of stuff to do, I've got a full front and back master cylinder and caliper re build kit and 4 x carby kits from Georgefix and new s/s brake lines to put in. I can't find anyone in Sydney who will do a proper ultasonic carby clean though. I've googled my head off without any luck.Automotive Imbecile.
Proud owner of 'The Swiftcicle'. (Swifty for short)
'78E Full Vetter Dresser.
1196 Big Bore Kit.Comment
-
You might be concerned about longevity.
These are rather small-looking from the pic and resemble some 'mini-coils' that are available. These smaller coils have the same (or close) specs as 'normal' coils, but when used with an older ignition system that doesn't have 'dwell control' will burn up...Fast, Cheap, Reliable... Pick any two
'78E original owner - resto project
'78E ???? owner - Modder project FJ forks, 4-piston calipers F/R, 160/80-16 rear tire
'82 XJ rebuild project
'80SG restified, red SOLD
'79F parts...
'81H more parts...
Other current bikes:
'93 XL1200 Anniversary Sportster 85RWHP
'86 XL883/1200 Chopper
'82 XL1000 w/1450cc Buell, Baker 6-speed, in-progress project
Cage: '13 Mustang GT/CS with a few 'custom' touches
Yep, can't leave nuthin' alone...Comment
-
They do look small, from the pix. Did you ask the seller if they are suitable for your model of bike?XS1100F 1980 European model. Standard. Dyna coils. Iridium plugs. XS750 final drive (sometimes). Micron fork brace. Progressive front springs. Geezer regulator/rectifier. Stainless 4 into 2 exhaust. Auto CCT (Venturer 1300) SOLD. New project now on the go. 1980 European model.Comment
-
They are exactly the same size as stock and they were advertised as XS1100.
Here's the actual ad once again.
http://www.ebay.com.au/itm/150810715...#ht_1292wt_698Automotive Imbecile.
Proud owner of 'The Swiftcicle'. (Swifty for short)
'78E Full Vetter Dresser.
1196 Big Bore Kit.Comment
Comment