Tweet
Im trying to figure out how it attaches and fit
and for the life of me cant figure it out,
heres a cpl of pics.
thanx in advance
and for the life of me cant figure it out,
heres a cpl of pics.
thanx in advance
-
pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url] -
To me, it looks like the mount uses the factory turn signal location to hold the frame. Probably uses a relocation bracket (that I dont see there) for the front turn signals also. It also looks like it uses 2 windshield bolts for the top, and something I can't quite make out for the bottom. 4 point on the fairing, 2 points on the bike.
My guess anyway
-
Not sure...........but if its mounted to that table, someone is gonna be unhappy.81H Venturer1100 "The Bentley" (on steroids) 97 Yamaha YZ250(age reducer) 92 Honda ST1100 "Twisty"(touring rocket) Age is relative to the number of seconds counted 'airing' out an 85ft. table-top.Comment
-
I just hope the iron in the background ISN'T ready to "clean" the windshield in the photo!!!Not sure...........but if its mounted to that table, someone is gonna be unhappy.
Ray Matteis
KE6NHG
XS1100 E '78 (winter project)
XS1100 SF Bob Jones worked on it!Comment
-
Hi Pete,
It attaches like this..
Basically it attaches to the same two screws on the front of the bottom yoke that the Sport indicators bolt to.
'84 SportComment
-
Hey Shapps,
Thanx for the pic and reply,
but i still cant figure out how it attaches,
nothing lines up, not sure if im missing any pieces or not.
The indicaters on mine are attached to the side of the bottom yoke,
this bracket doesnt come close to that.
Need a pic to see how its mounted, any1 got 1?pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
-
I will take mine off tomorrow an photograph for you
took me a while to figure out how to get it off
'81 XS1100R
4-2-1 exhaust Tranzac (Current)
Everything else stock (as far as I know)
Previous:
Honda scrambler horse( had to start somewhere
)
Yamaha DT175
Yamaha XT250
Yamaha TT500
Suzuki DR250
Yamaha XVS1100
Honda 750/4 K (basket case, current)Comment
-
mounting
1, the frame in the diagram needs to spin around.
2, the bottom holes pick up the bolts beside front blinker mounts on the bottom of triple tree
3, the 'ears' will pick up the headlight pivot bolts & the two small ears on top of the frame hold the fairing at the base of the screen
4, there is also a small mount at the base of the fairing itself that a small home made bracket also attached to the bolts at the bottom mount bolts will stabilise the whole show hope this helps, -----PS---- make sure you don't tighten the screen bolts down far, cause it will crack before you know itnever ride faster than your gaurdian angel
can fly
1981 rh 5N5
MIDNIGHTSPECIAL
1188cc
4 into 1 pipes with a transac muffler,
as the motorcycling gods intended everything else stock std
http://s856.photobucket.com/home/steptoexs11
http://steptoexs11.webs.com/
http://www.youtube.com/my_videos?feature=mhum
1982 vf750 sabreComment
-
Mount photo's
Hope these help
Top
'81 XS1100R
4-2-1 exhaust Tranzac (Current)
Everything else stock (as far as I know)
Previous:
Honda scrambler horse( had to start somewhere)
Yamaha DT175
Yamaha XT250
Yamaha TT500
Suzuki DR250
Yamaha XVS1100
Honda 750/4 K (basket case, current)Comment
-
'81 XS1100R
4-2-1 exhaust Tranzac (Current)
Everything else stock (as far as I know)
Previous:
Honda scrambler horse( had to start somewhere)
Yamaha DT175
Yamaha XT250
Yamaha TT500
Suzuki DR250
Yamaha XVS1100
Honda 750/4 K (basket case, current)Comment
-
Pics were great, thanx again Ozlad,
Thanx for all the replys, got it all fitted up.
I had a chrome cover covering the front of the bottom yoke,
so had to pull the forks out to get it fitted.
pete
new owner of
08 gen2 hayabusa
former owner
1981 xs1100 RH (aus) (5N5)
zrx carbs
18mm float height
145 main jets
38 pilots
slide needle shimmed .5mm washer
fitted with v/stax and uni pod filters
[url]http://www.youtube.com/watch?v=3pA8dwxmAVA&feature=mfu_in_order&list=UL[/url]Comment
Comment