"Shall We, Play... A... Game...?

[DiverRay]

OK, I'll go again. I DID get the egg first! This is all from memory, and I know some of this has already been done.
Board 1
A-1=? A-2=egg off a different bike A-3= hold down bolt for coils? A-4=? A-5=?
B-1= tank hold down washer B-2= rear shock washer B-3=top left mount for airbox B-4= pointer for timming/TDC B-5=?
C-1=headlamp adjuster C-2= cover for kick starter C-3=Fork caps C-4=? C-5= parts for airbox
D-1=? D-2= straps for airbox D-4= washers for triple tree?

Board 2
A-1= cover and wingnut for kick start lever A-2= caps for later model forks A-3= oil fill cap A-4= banjo bolts for brakes A-5= ?
B-1= ? B-2= carb/airbox clamps B-3= Carb/engine clamps B-4= carb/engine clamps? B-5= battery box parts
C-1= rear brake line holder C-2=? C-3=fender to front brake line holder C-4= rear brake push rod C-5= Air box top bracket
D-1= Special model holder for tank/frame cover

Board 3
B-1= wire holder, under the triple tree, Special model B-2&3 are Standard model wire holders

[dpotter58]

Board 2, b-5 washers for the battery box

[Bax]

Bd-2, C1 = Rear brake line holder.

---Bax

[Bax]

Bd-1, B3 = Right side air box mount bracket fitted washer.
Bd-1, D2 = Air Box mounting frame isolation pads

---Bax

[bikerphil]

Board 2 C2 is the Headlight Bucket Brace, for the special, yes?

Yes, I believe it is.

[XS-play]

This is fun, keep 'em coming.

[XS-play]

D-2 board 1 = seatpan rubber pads/washers.

I don't recall for certain, I think they are part of the Airbox Assembly.

[XS-play]

I’ll play
Board #2
A1 – kickstand cover & retaining screw YES [kickstart]
A2 – fork top air caps YES
A3 – Oil filler screw. Left those in the parking lot on several occasions YES
A4 – brake bleed screws BANJO BOLTS
B2-4 – carb boot retainer bands YES
C2- throttle cable attachment point HEADLIGHT BRACKET
C5 – airbox bracket YES

Good Job, newc4

[XS-play]

Board 2, C4 are rear master cylinder push rods.

Yes, I was just looking for stuff to powder coat one evening, All the Red is from that run.

I will take your word for the Counter Washers.

Board 1: I am not sure about C1 you could be correct, I have no clue about Board 2 C1 either. Board 2 C2 is the Headlight Bucket Brace, for the special, yes?

[XS-play]

I think A2 in the first picture is a bolt that holds a rotor on the wheel.

I think the "egg" is B1 in the second picture. This item looks like a homemade patch to put over the petcock holes when you are cleaning the gas tank.

Board 1 A2, is one of the unknown parts for me, not even sure if this belongs with an XS. It is too big to be a rotor bolt, though.

Ding Ding Ding Ding.... Winner Winner Chicken Dinner. Wow I am impressed. Bravo Zulu, RadioGuy

[MarkD]

D-2 board 1 = seatpan rubber pads/washers.

[bikerphil]

Board 2, C4 are rear master cylinder push rods.
Board 1, D4 are countershaft washers as in the second gear washer move.
Board 1, C1 is the Standard headlight coarse vertical beam adjuster.

[Radioguylogs]

A-2, first board looks like the egg! I'll need to look at the rest tonight, as I'm trying to get my XS to NOT leak gas from the tank/petcocks today.

I think A2 in the first picture is a bolt that holds a rotor on the wheel.

I think the "egg" is B1 in the second picture. This item looks like a homemade patch to put over the petcock holes when you are cleaning the gas tank.

I'll let other members identify the remaining parts.

[newc4]

I’ll play
Board #2
A1 – kickstand cover & retaining screw
A2 – fork top air caps
A3 – Oil filler screw. Left those in the parking lot on several occasions
A4 – brake bleed screws
B2-4 – carb boot retainer bands
C2- throttle cable attachment point
C5 – airbox bracket

[DiverRay]

A-2, first board looks like the egg! I'll need to look at the rest tonight, as I'm trying to get my XS to NOT leak gas from the tank/petcocks today.